high stability thin film flat chip resistors www.vishay.com for technical questions, contact: thinfilmchip@vishay.com document number: 28758 336 revision: 27-jun-12 tnpw e3 vishay this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 tnpw e3 precision thin film flat chip resistors are the perfect choice for most fields of modern electronics where highest reliability and stability is of major concern. typical applications include test and measuring equipment, medical equipment, industrial, and automotive. features ? low temperature coefficient and tight tolerances ( 0.1 %; 10 ppm/k) ? superior moisture resistivity ? 0.25 % (85 c; 56 days; 85 % rh) ? excellent overall stability at different environmental conditions ? 0.05 % (1000 h rated power at 70 c) ? aec-q200 qualified (sizes 0402 to 1206) ? waste gas resistant ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 applications ? test and measuring equipment ? medical equipment ? industrial equipment ? automotive notes ? tnpw 0402 without marking. (1) size not specified in en 140401-801. (2) rated voltage . the power dissipation on the resistor generat es a temperature rise against the local ambient, depending on the heat flow support of the printed-circ uit board (thermal resistance). using advanced tem perature level may require special considerat ions towards the choice of circuit board and solder mate rial. the rated dissipation applies only if the permitted film temperature is not ex ceeded. (3) measuring conditions in accordance with en 140401-801. standard electrical specifications description TNPW0402 e3 tnpw0603 e3 tnpw0805 e3 tnpw1206 e3 tnpw1210 e3 (1) tnpw2010 e3 tnpw2512 e3 (1) metric size rr 1005m rr 1608m rr 2012m rr 3216m rr 3225m rr 5025m rr 6332m resistance range 10 ? to 100 k ? 10 ? to 332 k ? 10 ? to 1 m ? 10 ? to 2 m ? 10 ? to 3.01 m ? 10 ? to 4.99 m ? 10 ? to 8.87 m ? resistance tolerance 1 %; 0.5 %; 0.1 % temperature coefficent 50 ppm/k; 25 ppm/k; 15 ppm/k; 10 ppm/k 50 ppm/k; 25 ppm/k rated dissipation, p 70 (2) 0.063 w 0.1 w 0.125 w 0.25 w 0.33 w 0.4 w 0.5 w operating voltage, u max. ac/dc 50 v 75 v 150 v 200 v 200 v 300 v 300 v permissible film temperature, ? f max. 155 c operating temperature range - 55 c to 125 c (155 c) thermal resistance (3) 870 k/w 550 k/w 440 k/w 220 k/w 170 k/w 140 k/w 110 k/w max. resistance change at p 70 ; ? r / r : 10 ? to 100 k ? 10 ? to 332 k ? 10 ? to 1 m ? 10 ? to 2 m ? 10 ? to 3.01 m ? 10 ? to 4.99 m ? 10 ? to 8.87 m ? 1000 h ?? 0.05 % ?? 0.05 % ?? 0.05 % ?? 0.05 % ?? 0.05 % ?? 0.05 % ?? 0.05 % 8000 h ?? 0.10 % ?? 0.10 % ?? 0.10 % ?? 0.10 % ?? 0.10 % ?? 0.10 % ?? 0.10 % 225 000 h ?? 0.30 % ?? 0.30 % ?? 0.30 % ?? 0.30 % ?? 0.30 % ?? 0.30 % ?? 0.30 % insulation voltage: u ins 1 min 75 v 100 v 200 v 300 v 300 v 300 v 300 v continuous 75 v 75 v 75 v 75 v 75 v 75 v 75 v failure rate: fit observed ?? 0.1 x 10 -9 /h ?? 0.1 x 10 -9 /h ?? 0.1 x 10 -9 /h ?? 0.1 x 10 -9 /h ?? 0.1 x 10 -9 /h ?? 0.1 x 10 -9 /h ?? 0.1 x 10 -9 /h p x r
document number: 28758 for technical questions, contact: thinfilmchip@vishay.com www.vishay.com revision: 27-jun-12 337 tnpw e3 high stability thin film flat chip resistors vishay this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 dimensions dimensions and mass type l (mm) w (mm) h (mm) t1/t2 (mm) mass (mg) TNPW0402 e3 1.0 0.05 0.5 0.05 0.35 0.05 0.2 0.10 0.65 tnpw0603 e3 1.6 0.10 0.85 0.10 0.45 0.10 0.3 0.20 2 tnpw0805 e3 2.0 0.15 1.25 0.15 0.45 0.10 0.4 0.20 5.5 tnpw1206 e3 3.2 0.15 1.6 0.15 0.55 0.10 0.5 0.25 10 tnpw1210 e3 3.2 0.15 2.45 0.15 0.60 0.15 0.5 0.25 16 tnpw2010 e3 5.0 0.15 2.5 0.15 0.60 0.15 0.6 0.25 28 tnpw2512 e3 6.3 0.20 3.1 0.15 0.60 0.15 0.6 0.25 39 solder pad dimensions type reflow soldering wave soldering a (mm) b (mm) l (mm) a (mm) b (mm) l (mm) TNPW0402 e3 0.4 0.6 0.5 - - - tnpw0603 e3 0.5 0.9 1.0 0.9 0.9 1.0 tnpw0805 e3 0.7 1.3 1.2 0.9 1.3 1.3 tnpw1206 e3 0.9 1.7 2.0 1.1 1.7 2.3 tnpw1210 e3 0.9 2.5 2.0 1.1 2.5 2.3 tnpw2010 e3 1.0 2.5 3.9 1.2 2.5 3.9 tnpw2512 e3 1.0 3.2 5.2 1.2 3.2 5.2 temperature coefficient and resistance range type tcr tolerance resistance e-series TNPW0402 e3 50 ppm/k 1 % 10r to 100k 24; 96 0.5 % 10r to 100k 24; 192 0.1 % 47r to 100k 25 ppm/k 1 % 10r to 100k 24; 96 0.5 % 10r to 100k 24; 192 0.1 % 47r to 100k 15 ppm/k 0.1 % 10 ppm/k 0.1 % tnpw0603 e3 50 ppm/k 1 % 10r to 332k 24; 96 0.5 % 10r to 332k 24; 192 0.1 % 25 ppm/k 1 % 10r to 332k 24; 96 0.5 % 10r to 332k 24; 192 0.1 % 15 ppm/k 0.1 % 47r to 332k 10 ppm/k 0.1 % tnpw0805 e3 50 ppm/k 1 % 10r to 1m0 24; 96 0.5 % 10r to 1m0 24; 192 0.1 % 25 ppm/k 1 % 10r to 1m0 24; 96 0.5 % 10r to 1m0 24; 192 0.1 % 15 ppm/k 0.1 % 47r to 1m0 10 ppm/k 0.1 % tnpw1206 e3 50 ppm/k 1 % 10r to 2m0 24; 96 0.5 % 10r to 2m0 24; 192 0.1 % 25 ppm/k 1 % 10r to 2m0 24; 96 0.5 % 10r to 2m0 24; 192 0.1 % 15 ppm/k 0.1 % 47r to 2m0 10 ppm/k 0.1 %
www.vishay.com for technical questions, contact: thinfilmchip@vishay.com document number: 28758 338 revision: 27-jun-12 tnpw e3 vishay high stability thin film flat chip resistors this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? the product can be ordered using either the part number or the product description. tnpw1210 e3 50 ppm/k 1 % 10r to 3m01 24; 96 0.5 % 10r to 3m01 24; 192 0.1 % 47r to 2m13 25 ppm/k 1 % 10r to 3m01 24; 96 0.5 % 10r to 3m01 24; 192 0.1 % 47r to 2m13 15 ppm/k 0.1 % 10 ppm/k 0.1 % tnpw2010 e3 50 ppm/k 1 % 10r to 4m99 24; 96 0.5 % 10r to 4m99 24; 192 0.1 % 47r to 1m0 25 ppm/k 1 % 10r to 4m99 24; 96 0.5 % 10r to 4m99 24; 192 0.1 % 47r to 1m0 tnpw2512 e3 50 ppm/k 1 % 10r to 8m87 24; 96 0.5 % 10r to 8m87 24; 192 0.1 % 47r to 1m0 25 ppm/k 1 % 10r to 8m87 24; 96 0.5 % 10r to 8m87 24; 192 0.1 % 47r to 1m0 temperature coefficient and resistance range type tcr tolerance resistance e-series part number and product description part number: tnpw12061k32deea type/size resistance tolerance tcr pac k ag i n g special TNPW0402 tnpw0603 tnpw0805 tnpw1206 tnpw1210 tnpw2010 tnpw2512 r = decimal k = thousand m = million (4 digits) b = 0.1 % d = 0.5 % f = 1.0 % h = 50 ppm/k e = 25 ppm/k x = 15 ppm/k y = 10 ppm/k ea ec ed eg en ey up to 2 digits blank = standard product description: tnpw1206 1k32 0.5 % t-9 et1 e3 tnpw1206 1k32 0.5 % t-9 et1 e3 type/size resistance tolerance tcr packaging lead (pb)-free TNPW0402 tnpw0603 tnpw0805 tnpw1206 tnpw1210 tnpw2010 tnpw2512 examples: 54r1 = 54.1 ? 1k32 = 1320 ? 0.1 % 0.5 % 1.0 % t- 2 = 50 ppm/k t- 9 = 25 ppm/k t- 1 0 = 15 ppm/k t- 1 3 = 10 ppm/k et1 et6 et7 e67 e52 e75 e3 = pure tin termination finish tw120 p n 61k32deea
document number: 28758 for technical questions, contact: thinfilmchip@vishay.com www.vishay.com revision: 27-jun-12 339 tnpw e3 high stability thin film flat chip resistors vishay this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note (1) 1000 pieces packaging is avail able only for precision resistors with tole rance 0.1 % and temperature coefficient ? 25 ppm/k. description production is strictly controlled and follows an extensive set of instructions established for reproducibility. a homogeneous film of metal al loy is deposited on a high grade ai 2 o 3 ceramic substrate and conditioned to achieve the desired temperature coefficient. specially designed inner contacts are deposited on both sides. a special laser is used to achieve the target value by smoothly fine trimming the resistive layer without damaging the ceramics. a further conditioning is applied in order to stabilize the trimming result. the resistor elements are covered by a protective coating designed for electrical, mechanical and climatic protection. the terminations re ceive a final pure tin on nickel plating. the result of the determined production is verified by an extensive testing procedure on 100 % of the individual chip resistors. this includes pulse load screening for the elimination of products with a potential risk of early life failures according to en 140401-801, 2.1.2.2. only accepted products are laid directly into the tape in accordance with en 60286-3 . assembly the resistors are suitable for processing on automatic smd assembly systems. they are su itable for automa tic soldering using wave, reflow or vapour phase as shown in iec 61760-1 . the encapsulation is resistant to all cleaning solvents commonly used in the electronics industry, including alcohols, esters and aqueous solutions. the suitability of conformal coatings , if applied, shall be qualified by appropriate means to ensure the long-term stability of the whole system. the resistors ar e rohs compliant, the pure tin plating provides compat ibility with lead (pb)-free and lead-containing soldering proc esses. the immunity of the plating against tin whisker growth has been proven under extensive testing. all products comply with the gadsl (2) and the cefic-eeca-eicta (3) list of legal restrictions on hazardous substances. this includes full compliance with the following directives: ? 2000/53/ec end of vehicle life directive (elv) and annex ii (elv ii) ? 2011/65/eu restriction of the use of hazardous substances directive (rohs) ? 2002/96/ec waste electrical and electronic equipment directive (weee) the resistors are halogen-free according to jedec js709a definition. solderability is specified for 2 years after production or re-qualification. the permitt ed storage time is 20 years. related products the tnpw with snpb termination plating is designed for those applications, where lead bearing terminations are mandatory. for ordering tnpw with snpb terminations please refer to latest edition of data sheet tnpw, document number 31006. tnps .... escc high-reliability thin film chip resistors are the premium choice for design and manufacture of equipment, where matured technology and proven reliability are of utmost importance. they are regularly used in communication and research satellites and fit equally well into aircraft and military electr onic systems. approval of the tnps .... escc products is granted by the european space components coordination and registered in the escc qualified parts list, rep0 05, document number 28789. notes (2) global automotive declar able substance list, see www.gadsl.org . (3) cefic (european chemical industry counci l), eeca (european electronic component manufac turers association) , eicta (european tra de organisation representing the inform ation and communications technology and consumer electronics), see www.eicta.org ? issue ? environment policy ? chemicals ? chemicals for electronics. packaging type code quantity carrier tape width pitch reel diameter TNPW0402 e3 et7 = ed 10 000 paper tape acc. iec 60286-3 type i 8 mm 2 mm 180 mm / 7" tnpw0603 e3 tnpw0805 e3 tnpw1206 e3 tnpw1210 e3 e52 = en 1000 (1) 4 mm 180 mm / 7" et1 = ea 5000 et6 = ec 20 000 4 mm 330 mm / 13" tnpw2010 e3 e75 = ey 1000 blister tape acc. iec 60286-3 type ii 12 mm 4 mm 180 mm / 7" tnpw2512 e3 e75 = ey 1000 e67 = eg 2000
www.vishay.com for technical questions, contact: thinfilmchip@vishay.com document number: 28758 340 revision: 27-jun-12 tnpw e3 vishay high stability thin film flat chip resistors this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 functional performance note (1) typical figures. hf-charact eristic also depends on te rmination and circuit design. 120 110 100 90 8 0 70 60 10 100 1k 10k 100k non-linearity non-linearity a 3 in db resistance value in tnpw0603 e3 tnpw1206 e3 TNPW0402 e3 tnpw0 8 05 e3 3 2 1 100 1k 10k 100k 1m current noise current noise in v/v resistance value in TNPW0402 e3 tnpw0 8 05 e3 0.5 0.3 0.1 0.01 0.03 0.05 tnpw0603 e3 tnpw1206 e3 60 40 20 0 - 40 - 60 - 8 0 1 5 10 50 100 frequency f in mhz hf performance (1) phase an g le in ? tnpw0603 e3 10 100 1 k 4.75 k 10 k 500 1000 60 40 20 0 - 20 - 40 - 60 - 8 0 tnpw0603 e3 hf performance (1) 1510 50 100 500 1000 frequency f in mhz [z]-ro in % ro 10 100 1 k 4.75 k 10 k 60 40 20 0 - 20 - 40 - 60 - 8 0 phase an g le in ? 1 5 10 50 100 frequency f in mhz hf performance (1) tnpw0 8 05 e3 10 100 1 k 10 k 500 1000 60 40 20 0 - 20 - 40 - 60 - 8 0 [z]-ro in % ro hf performance (1) 1510 50 100 500 1000 frequency f in mhz tnpw0 8 05 e3 10 100 1 k 10 k
document number: 28758 for technical questions, contact: thinfilmchip@vishay.com www.vishay.com revision: 27-jun-12 341 tnpw e3 high stability thin film flat chip resistors vishay this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 90 8 0 70 60 50 40 30 20 10 0 temperature rise 0 0.1 0.2 0.3 0.4 0.5 power in w temperature rise in k 0.6 0.7 0402 0603 0 8 05 1206 1210 2010 2512 deratin g 120 100 8 0 60 40 20 0 - 55 - 25 0 25 50 75 100 125 150 175 ambient temperature in c rated power in % 70 en 3k 1k 100 10 10r 100r 1k 10k 100k test volta g e in v tnpw0 8 05 e3 tnpw0603 e3 sin g le-pulse hi g h volta g e overload test 1.2/50 s en140000 4.27 resistance value in sin g le-pulse hi g h volta g e overload test 10/700 s en140000 4.27 resistance value in test volta g e in v tnpw0 8 05 e3 tnpw0603 e3 100 w 10 w 1 w 0.1 w 10 s pulse duration t i permissible pulse power p i, max. 100 s 1 ms 10 ms 100 ms 1 s 10 s maximum pulse load p i, max. for sin g le pulses tnpw1206 e3 tnpw0 8 05 e3 tnpw0603 e3 conditions: p 0, n 1000 and u i u i, max. 100 w 10 w 1 w 0.1 w 10 s permissible pulse power p i, max. 100 s 1 ms 10 ms 100 ms 1 s 10 s pulse duration t i tnpw1206 e3 tnpw0 8 05 e3 tnpw0603 e3 conditions: p max. p max. (incl u ding derating) and u i u i, max. maximum pulse load p i, max. for continuous pulses
www.vishay.com for technical questions, contact: thinfilmchip@vishay.com document number: 28758 342 revision: 27-jun-12 tnpw e3 vishay high stability thin film flat chip resistors this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 test and requirements all tests are carried out in accordance with the following specifications: iec 60115-1, generic specification (includes tests) en 140400, sectional specification (includes schedule for qualification approval) en 140401-801, detail specification (includes schedule for conformance inspection) the testing also covers most of the requirements specified by eia/is-703 and jis-c-5202. the tests are carried out under standard atmospheric c onditions in accordance with iec 60068-1, 5.3. climatic category lct/uct/56 (rated temperature range: lower ca tegory temperature, upper category temperature; damp heat, long term, 56 days) is valid. unless otherwise specified the following values apply: temperature: 15 c to 35 c relative humidity: 45 % to 75 % air pressure: 86 kpa to 106 kpa (860 mbar to 1060 mbar). the components are mounted for testing on boards in accordance with en 60115-1, 4.31 unless otherwise specified. the parameters stated in the test procedures and requirements table are based on the required tests and permitted limits of en 140401-801. 10 000 v 1000 v 100 v 10 v 10 s pulse duration t i permissible pulse volta g e u i, max. 100 s 1 ms 10 ms 100 ms 1 s 10 s tnpw1206 e3 tnpw0 8 05 e3 tnpw0603 e3 conditions: p i p i, max. maximum pulse volta g e u i, max. test procedures and requirements en 60115-1 clause iec 60068-2 test method test procedure requirements permissible change stability for product types: TNPW0402 e3 tnpw0603 e3 tnpw0805 e3 tnpw1206 e3 tnpw1210 e3 tnpw2010 e3 tnpw2512 e3 4.5 - resistance 1 %; 0.5 %; 0.1 % 4.8.4.2 - temperature coefficient at (20/- 55/20) ? c and (20/125/20) c 50 ppm/k; 25 ppm/k; 15 ppm/k; 10 ppm/k 4.25.1 - endurance at 70 ? c u = or u = u max. ; whichever is the less severe; 1.5 h on; 0.5 h off; 70 c; 1000 h (0.05 % r +0.01 ? ) 70 ? c; 8000 h (0.1 % r +0.02 ? ) 4.25.3 - endurance at upper category temperature 125 c; 1000 h 155 c; 1000 h (0.05 % r + 0.01 ? ) (0.1 % r + 0.02 ? ) p 70 x r
document number: 28758 for technical questions, contact: thinfilmchip@vishay.com www.vishay.com revision: 27-jun-12 343 tnpw e3 high stability thin film flat chip resistors vishay this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 4.24 78 (cab) damp heat, steady state (40 ? ? 2) c; 56 days; (93 3) % rh (0.1 % r + 0.01 ? ) 4.23 climatic sequence: ? (0.1 % r +0.02 ? ) 4.23.2 2 (bb) dry heat uct; 16 h 4.23.3 30 (db) damp 55 c; 24 h; > 90 % rh; 1 cycle 4.23.4 1 (ab) cold lct; 2 h 4.23.5 13 (m) low air 8.5 kpa; 2 h; 25 10 c 4.23.6 30 (db) damp heat, cyclic 55 c; 5 days; > 95 to 100 % rh; 5 cycles 4.23.7 - dc load u = ? u max. ; 1 min lct = - 55 c uct = 125 c - 1 (ab) cold - 55 c; 2 h ? (0.05 % r +0.01 ? ) 4.19 14 (na) rapid change of temperature 30 min at lct and 30 min at uct; lct = - 55 c; uct = 125 c; 1000 cycles ? (0.1 % r +0.01 ? ) 4.13 - short time overload u = 2.5 x or u =2 x u max. ; whichever is the less severe; 5 s ? (0.05 % r +0.01 ? ) 4.27 - single pulse high voltage overload severity no. 4: u = 10 x or u =2 x u max. ; whichever is the less severe; 10 pulses 10 s/700 s ? (0.5 % r +0.05 ? ) no visible damage 4.37 - periodic electric overload u = or u =2 x u max. ; whichever is the less severe; 0.1 s on; 2.5 s off; 1000 cycles ? (0.5 % r +0.05 ? ) no visible damage 4.22 6 (fc) vibration endurance by sweeping; 10 hz to 2000 hz; no resonance; amplitude ? 1.5 mm or ? 200 m/s 2 ; 7.5 h ? (0.05 % r +0.01 ? ) no visible damage test procedures and requirements en 60115-1 clause iec 60068-2 test method test procedure requirements permissible change stability for product types: TNPW0402 e3 tnpw0603 e3 tnpw0805 e3 tnpw1206 e3 tnpw1210 e3 tnpw2010 e3 tnpw2512 e3 p 70 x r p 70 x r p 70 x r 15 x p 70 x r
www.vishay.com for technical questions, contact: thinfilmchip@vishay.com document number: 28758 344 revision: 27-jun-12 tnpw e3 vishay high stability thin film flat chip resistors this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 4.17.2 58 (td) solderability solder bath method; snpb40; non-activated flux (215 3) c; (3 0.3) s good tinning ( ? 95 % covered); no visible damage solder bath method; snag3cu0.5 or snag3.5; non-activated flux (235 3) c; (2 0.2) s 4.18.2 58 (td) resistance to soldering heat solder bath method; (260 5) c; (10 1) s ? (0.02 % r +0.01 ?? ) 4.29 45 (xa) component solvent resistance isopropyl alcohol + 50 c; method 2 no visible damage 4.32 21 (ue 3 ) shear (adhesion) rr 1005m and rr 1608m; 9 n no visible damage rr 2012m and rr 3216m: 45 n 4.33 21 (ue 1 ) substrate bending depth 2 mm, 3 times ? (0.05 % r +0.01 ?? ) no visible damage, no open circuit in bent position 4.7 - voltage proof u rms = u ins ; 60 5 s no flashover or breakdown 4.35 - flammability iec 60695-11-5, needle flame test; 10 s no burning after 30 s - - damp heat (85 ? 5) c; 56 days (85 ? 5) % rh (0.25 r + 0.05 ? ) test procedures and requirements en 60115-1 clause iec 60068-2 test method test procedure requirements permissible change stability for product types: TNPW0402 e3 tnpw0603 e3 tnpw0805 e3 tnpw1206 e3 tnpw1210 e3 tnpw2010 e3 tnpw2512 e3
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
